Browan BW2250 Page 24 User Manual Download

Page: 24 / 75

BROWAN COMMUNICATIONS

Page

Reset –

reboot device and restore systems to factory default

Upgrade

– Upgrade the firmware remotely

In the following sections, short references for all menu items are presented.

Status

Status | Device Status

The device status page shows important information for the BW2250, its system status and network
configuration.

Figure 11 – Device Status

System Version

display the current version of the firmware loaded to the AP

This is important information for support requests and for preparing firmware
upgrading

Uptime –

indicates the time, expressed in days, hours and minutes since the system was last

rebooted.

System Time

– shows the current time of the BW2250

Wlan1 MAC / Wlan 2 MAC –

shows the MAC addresses of the two wireless interfaces of the BW2250

Free System Memory –

indicates the memory currently available in the BW2250

Total System Memory –

indicates the total memory in the BW2250

LAN Mode –

indicate static IP or DHCP client is used for BW2250 LAN IP address

LAN IP –

shows the LAN IP address of BW2250

LAN Mask

– shows the LAN Network Mask of BW2250

Gateway

– shows the default gateway of BW2250

Summary of Contents for BW2250











































































Search results

Summary of Contents for BW2250

Reviews:

Related manuals for BW2250

Brands by name

Popular brands

Browan BW2250, User Manual

Search results

Summary of Contents for BW2250

Reviews:

Related manuals for BW2250

Brands by name

Popular brands