background image

Setting Up the Printer 

3

1

Using the 

Rechargeable Ni-MH 

Battery (Optional)

1

Installing the Rechargeable 
Ni-MH Battery

1

a

Open the battery cover (1) by pressing 
the cover latch (2).

 

1 Battery cover
2 Cover latch

b

Swing the cover open and remove it.

c

Check the orientation of the battery 
connector, and then gently insert the 
connector (4) into the terminal (3) on the 
inside of the battery compartment.

 

3 Terminal

4 Battery connector

NOTE

With the printer positioned as shown 
below, the red wire of the battery 
connector (4) will be on the left side.

 

d

Grasp the battery removal ribbon, which 
is attached to the inside of the battery 
compartment. Make sure that enough 
ribbon is exposed after the rechargeable 
Ni-MH battery installed so that you can 
pull the ribbon to remove the battery.

e

While holding onto the ribbon, tilt the 
rechargeable Ni-MH battery and insert it 
into the battery compartment. After the 
rechargeable Ni-MH battery passes the 
outer edges of the compartment, press it 
securely into position.

NOTE

• Make sure that the side of the 

rechargeable Ni-MH battery marked 
“Ni-MH” faces away from the battery 
compartment, otherwise the battery cover 
will not close properly.

• The rechargeable Ni-MH battery contains 

a heat sensor that stops the flow of 
electricity if the battery overheats.

 

f

Attach the battery cover to the end of the 
battery compartment opposite the 
AC/DC connector. Close and latch the 
cover. If necessary, gently push the 
cover latch towards the AC/DC 
connector until it latches.

NOTE

• Be careful that you do not pinch the 

battery connector cord.

• The voltage supplied by the rechargeable 

Ni-MH battery fluctuates. The printing 
speed may also fluctuate depending on 
the voltage.

 

2

1

4

3

Summary of Contents for PocketJet PJ-673












































































Reviews: