Brother NC-series User Manual Download | Manualshive

Page: 140 / 143

background image

USER’S GUIDE

A-20

If the red LED does not go out after about two minutes, check to make sure
that you correctly entered all parameters and that your network connections
are good. Then power the print server off and then on again, enter the

SET

LOAD ENABLE

command, and exit the remote console to retry the

download.

Downloading from a VINES Server

To download from a Banyan VINES file server, first copy the load file into
any directory on your file server (for example, E:). Then use the BRAdmin
utility (see Chapter 9 Section C) to download the new firmware. Go to the
main screen, select the File menu, and choose Reload. Then select the
drive and directory in which the load file is located, click on the file name,
and click on OK to get the Firmware Reload menu. Select the desired
print server(s) and click on Reload. Click on OK when the reload is
complete.

Obtaining Firmware Updates

To get latest firmware updates, "access" the Brother WWW server on
www.brother.com.

«
...
138
139
140
141
142
...
»

Summary of Contents for NC-series
















































































































































Reviews:

No comments

Related manuals for NC-series

Brand: IBM Pages: 102

Brand: DataCard Pages: 7

Brand: QMS Pages: 104

Brand: Oki Pages: 215

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 6

Brand: Durst Pages: 2

OKIPAGE 8p Plus

Brand: Oki Pages: 18

Brand: Oki Pages: 44

NPort P5250A Series

Brand: Moxa Technologies Pages: 2

Brand: Panduit Pages: 85

Brand: Wang Pages: 39

Brand: Fujitsu Pages: 9

Brand: Fujitsu Pages: 7

Brand: Fujitsu Pages: 6

Brand: Fujitsu Pages: 5

Brand: Fujitsu Pages: 6

Brand: Fujitsu Pages: 6

Brand: Fujitsu Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands