Brother NC-series User Manual Download

Page: 5 / 143

TABLE OF CONTENTS

iii

CHAPTER 5

NetBIOS CONFIGURATION (NetBEUI/TCP/IP) 5-1

Introduction 5-1

Print Server Configuration 5-2

Changing the domain name using TELNET or BRCONFIG 5-3

NetBIOS Port Monitor for Windows 95/98, NT4.0 5-4

Installing the Brother Peer to Peer Print Software (NetBIOS) 5-4
Associating to the printer 5-5
Adding a second Network Direct Print Port 5-7

LAN Server/Warp Server Configuration 5-8

Server Configuration 5-8
Workstation Configuration 5-8

CHAPTER 6

APPLETALK NETWORK CONFIGURATION 6-1

AppleTalk 6-1

Macintosh Configuration 6-2

Operation 6-2

How to Select the Print Server 6-2

Printing Binary Graphics 6-3

Changing the Configuration 6-4

CHAPTER 7

WINDOWS NT (DLC/LLC) CONFIGURATION 7-1

Configuring DLC on Windows NT 7-1

Windows NT 4.0 Printer Setup 7-2
Windows NT 3.5x Printer Setup 7-3

Configuring DLC on Other Systems 7-4

Summary of Contents for NC-series
















































































































































Search results

Summary of Contents for NC-series

Reviews:

Related manuals for NC-series

Brands by name

Popular brands

Brother NC-series, User Manual

Search results

Summary of Contents for NC-series

Reviews:

Related manuals for NC-series

Brands by name

Popular brands