Brother MFC-9140CDN User Manual Download Page 131

Page: 131 / 243

Troubleshooting

121

Unusable Device

Remove the Device.

Turn the power off

and back on again.

A defective USB device or a
high power consumption USB
device has been connected to
the USB direct interface.

Unplug the device from the USB direct

interface. Press and hold down

to turn the

machine off, and then turn it on again.

Unusable Device

A USB device or USB Flash
memory drive that is not
supported/is encrypted has
been connected to the USB
direct interface.

Unplug the device from the USB direct
interface (see the specifications for supported
USB Flash memory drives in

Printing data from

a USB Flash memory drive or digital camera
supporting mass storage (For MFC-9340CDW)

on page 59).

USB Access Error

The device was removed from
USB direct interface while
accessing the USB device.

Press

. Reinsert the device and try to

store the scanned data to the device.

USB

Write-protected

The protect switch of the USB
Flash memory drive is on.

Turn off the protect switch of the USB Flash
memory drive.

WT Box End Soon

The waste toner box is near the
end of its life.

Buy a new waste toner box before you get a

Replace WT Box

message.

Error Message

Cause

Action

Summary of Contents for MFC-9140CDN




















































































































































































































































Search results

Summary of Contents for MFC-9140CDN

Reviews:

Brands by name

Popular brands

Brother MFC-9140CDN, User Manual

Search results

Summary of Contents for MFC-9140CDN

Reviews:

Brands by name

Popular brands