Brother Innov-is NV4000D Service Manual Download Page 305

Page: 305 / 381

4 - 11

Adjustment

Adjustment

Clearance between needle and rotary hook point adjustment

1. Remove the front cover, and turn the power on while pressing [SW3] and [SW4] on the main PCB assembly.

2. Press [SW4] four times (select test mode "4" and then "" when the front cover is attached) to move the needle bar

to the left base line.

3. Turn the power off.

4. Remove the 2 flat screws (M4), and then remove needle plate A from the feed base.

5. Loosen the screw (M3X20).

6. Turn the pulley by hand until the right edge of the needle is aligned with the tip of the outer rotary hook.

7. Adjust the clearance between the needle and the outer rotary hook (front and back) to 0.1 mm or less using the

adjusting screw.

8. Tighten the screw (M3X20).

Back

Front

Tip

0.1mm or less

Needle

Adjusting
screw

Summary of Contents for Innov-is NV4000D






























































































































































































































































































































































































Search results

Summary of Contents for Innov-is NV4000D

Reviews:

Related manuals for Innov-is NV4000D

Brands by name

Popular brands

Brother Innov-is NV4000D, Service Manual

Search results

Summary of Contents for Innov-is NV4000D

Reviews:

Related manuals for Innov-is NV4000D

Brands by name

Popular brands