Brother BAS-300G-484 Instruction Manual Download Page 22

Page: 22 / 88

3. INSTALLATION

BAS-300G-484, BAS-300G-484 SF

<Power supply motor P.C. board>

<PMD P.C. board>

Connector

Connection location on

power supply motor P.C.

board

Cord clamp/cable tie

Machine head memory 7-pin

P3 (HEAD-M)

(4)

Upper shaft motor 3-pin

P4 (UVW)

(5)

Synchronizer 14-pin

P5 (SYNC)

(5), (6)

Connector

Connection location on

PMD P.C. board

Cable tie

Work clamp pulse motor 4-pin black

P3 (PPM)

(5), (6)

Thread trimmer solenoid 6-pin

P6 (SOL1)

(5), (6)

Tension release solenoid 4-pin

P7 (SOL2)

(5), (6)

Y pulse motor 4-pin blue

P8 (YPM)

(5), (6)

X pulse motor 4-pin white

P10 (XPM)

(5), (6)

(Continued on next page)

Press
the tab.

NOTE:

Route the X, Y and work clamp pulse motor
harnesses so that they do not touch the
PMD P.C.

*1:

Be sure to make the ground connection.

(Refer to "3-10. Connecting the ground

wire".)

*2:

Only applicable to -484 SF specifications

4651M

Summary of Contents for BAS-300G-484

























































































Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands

Brother BAS-300G-484, Instruction Manual

Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands