Brother BAS-300G-484 Instruction Manual Download Page 48

Page: 48 / 88

6. USING THE OPERATION PANEL (ADVANCED OPERATIONS)

BAS-300G-484, BAS-300G-484 SF

Next, set the intermittent presser foot height.

* This setting is only applicable to -484 SF specifications.

For -484 specifications, proceed to step 7.

THREAD/CLAMP indicator flashes

Press the SELECT key.

Press the or key to set the intermittent presser foot
height to be recorded.

TEST indicator illuminates, MENU indicator flashes

Press the SELECT key.

•

If setting further user programs, select the user

program number and then repeat steps 2 to 7.

End user program recording mode.

TEST indicator switches off, MENU indicator illuminates

Press the TEST key.

This completes the recording of a user program.

•

The user program number will flash in the PROGRAM

No. display, and the sewing machine will switch to
home position detection standby.

4970Q

4971Q

4969Q

Summary of Contents for BAS-300G-484

























































































Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands

Brother BAS-300G-484, Instruction Manual

Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands