Brother BAS-300G-484 Instruction Manual Download Page 33

Page: 33 / 88

4. PREPARATION BEFORE SEWING

BAS-300G-484, BAS-300G-484 SF

4-7. Thread tension

[Thread tension reference]

Upper thread

#4 or similar

Lower thread

#4 or similar

Upper thread tension (N)

3.0

−

3.5

Lower thread tension (N)

1.2

−

1.5

Pre-tension (N)

0.3

−

0.6

Needle

DP x 17 #25

Normal sewing speed

1,300 sti/min

4-7-1. Lower thread tension

Adjust the lower thread tension by turning the adjusting
screw (1).

4-7-2. Upper thread tension

1. Turn the tension nut (1) (main tension) to adjust the

tension as appropriate for the material being sewn.

2. Use the tension nut (2) (sub tension) to adjust the upper

thread trailing length to about 45 mm.

Weaker

Stronger

Weaker

Stronger

Weaker

Stronger

3185Q

4666M

Summary of Contents for BAS-300G-484

























































































Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands

Brother BAS-300G-484, Instruction Manual

Search results

Summary of Contents for BAS-300G-484

Reviews:

Related manuals for BAS-300G-484

Brands by name

Popular brands