Brother 888-G60 Operation Manual Download Page 11

Page: 11 / 68

Names of Machine Parts

GE
T

G RE

The appearance may differ depending on the machine
model you purchased.

■

Main parts

Top cover
(page 16)

Thread guide plate (page 17)

Thread guide cover

Bobbin winding thread guide and pretension disk
(page 18)

Spool cap (page 17)

Spool pin (page 17)

Bobbin winder (page 16)

LCD (liquid crystal display) (page 12)

Operation panel (page 10)

Operation buttons (page 10)

Embroidery unit

Thread cutter (page 22)

Needle threader lever (page 22)

Handwheel

Turn the handwheel toward you (counterclockwise) to raise and
lower the needle.

Handle

Carry the machine by its handle when transporting.

Presser foot lever

Raise and lower the presser foot lever to raise and lower the
presser foot.

Main power switch (page 11)

Power supply jack (page 11)

Air vent

The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.

USB port (for a USB flash drive) (page 47)

■

Needle and presser foot section

Needle bar thread guide (page 21)

Needle plate

Needle plate cover (page 19)

Bobbin cover/bobbin case (page 19, 50)

Embroidery foot (page 34, 50)

The embroidery foot helps control fabric flexibility for better
stitch consistency.

Embroidery foot screw (page 51)

Use the embroidery foot screw to hold the embroidery foot in
place.

Chapter

GETTING READY

Note

• Be sure to install the latest software.

Refer to “Updating Your Machine’s Software” on
page 57.

Names of Machine Parts

a b

e f

Summary of Contents for 888-G60





































































Search results

Summary of Contents for 888-G60

Reviews:

Related manuals for 888-G60

Brands by name

Popular brands

Brother 888-G60, Operation Manual

Search results

Summary of Contents for 888-G60

Reviews:

Related manuals for 888-G60

Brands by name

Popular brands