Brother 09055CDN Service Manual Download | Manualshive

Page: 137 / 590

background image

2-98

Confidential

■

Error code EE

Unavailability of communication after connecting to the wireless LAN PCB is detected.
(Wireless LAN model only)

■

Error code EF

The supplied power is unstable.

<User Check>

- Turn OFF the power switch, and turn it ON again after a while.

Print Unable EE
Turn the power off and then back on again.

Step

Cause

Remedy

1

Harness connection failure of
wireless LAN PCB

Check the harness connection of the
wireless LAN PCB and reconnect it.

2

Wireless LAN PCB failure

Replace the wireless LAN PCB.

3

Main PCB failure

Replace the main PCB ASSY.

Print Unable EF
Turn the power off and then back on again.

Step

Cause

Remedy

1

The irregular power supply is
detected

Replace the low-voltage power supply
PCB ASSY. Reset the irregular power
supply detection counter following the
procedure described in

MACHINE ERROR EF IS DETECTED
AND THE LOW-VOLTAGE POWER
SUPPLY PCB ASSY IS REPLACED"
in Chapter 4

2

Main PCB failure

Replace the main PCB ASSY.

Note:

The irregular power supply detection error (Machine Error EF) occurs when there is a large
distortion of the power supply voltage supplied to the machine.
In this case, if the same power supply is used, the same error might occur again even if the
low-voltage power supply PCB ASSY is replaced. For this reason, be sure to ask the user
to rearrange the installation environment.

«
...
135
136
137
138
139
...
»

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 09055CDN

Brand: Datamax Pages: 19

Brand: Canon Pages: 2

DocuPrint 4850 NPS

Brand: Xerox Pages: 276

Brand: Oki Pages: 192

Brand: Posnet Pages: 2

Brand: Kyocera Pages: 173

Brand: Oki Pages: 239

Brand: WOOSIM Pages: 27

Brand: Epson Pages: 10

2070 Color Jetprinter

Brand: Lexmark Pages: 78

Brand: Whip Mix Pages: 28

Brand: Citizen Pages: 127

Brand: Citizen Pages: 36

Brand: Citizen Pages: 19

CT-S651 Type II

Brand: Citizen Pages: 59

WorkCentre 3045

Brand: Xerox Pages: 210

Brand: AGFA Pages: 192

Brand: TRILAB Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands