Brother 09055CDN Service Manual Download

Page: 118 / 590

2-79

Confidential

■

Error code A5

Scanning failure upon FAX transmission. (First side) (Document scanner unit failure for the
first time.)

<User Check>

- Turn the power OFF/ON, and try scanning again.

■

Error code A6

Scanning failure upon FAX transmission. (First side) (Document scanner unit failure for the
second time or later.)

■

Error code A7

Scanning color parameter file failure.

Error code A8

Scanning color parameter error for recording the image.

Scan Unable
Remove the original document. Turn the power off, then on again.

Step

Cause

Remedy

Scanning error

Turn the power switch OFF and ON.
Then, try scanning again.

Scan Unable A6
See Troubleshooting and routine maintenance chapter in User’s Guide.

Step

Cause

Remedy

White level data failure

Perform the acquisition of white level data.
(

Function code 55

)

Document scanner unit failure
(First-side)

Replace the document scanner unit.

Main PCB failure

Replace the main PCB ASSY.

Scan Unable A7
See Troubleshooting and routine maintenance chapter in User’s Guide.

Scan Unable A8
See Troubleshooting and routine maintenance chapter in User’s Guide.

Step

Cause

Remedy

White level data failure

Perform the acquisition of white level data.
(

Function code 55

)

Document scanner unit failure

Replace the document scanner unit.

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for 09055CDN















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands

Brother 09055CDN, Service Manual

Search results

Summary of Contents for 09055CDN

Reviews:

Related manuals for 09055CDN

Brands by name

Popular brands