background image

2-2

Model SLA7840

Section 2 Installation

Installation and Operation Manual

X-PR-SLA7800-RT-eng

Part Number: 541B048AAG

August, 2009

2-4 Return Shipment

Prior to returning any instrument to the factory, contact your nearest Brooks
location for a Return Materials Authorization Number (RMA#). This can be
obtained from one of the following locations:

Brooks Instrument

407 W. Vine Street
P.O. Box 903
Hatfield, PA 19440 USA
Toll Free (888) 554 FLOW (3569)
Tel (215) 362 3700
Fax (215) 362 3745
E-mail: [email protected]
www.BrooksInstrument.com

Brooks Instrument

Brooks Instrument

Neonstraat 3

1-4-4 Kitasuna Koto-Ku

6718 WX Ede, Netherlands

Tokyo, 136-0073 Japan

P.O. Box 428

Tel  +81 (0) 3 5633 7100

6710 BK Ede, Netherlands

Fax +81 (0) 3 5633 7101

Tel +31 (0) 318 549 300

Email:  [email protected]

Fax +31 (0) 318 549 309
E-mail: [email protected]

 Instrument must have been purged in accordance with the following:

Completion of form RPR003-1, Brooks Instrument Decontamination
Statement. A copy of this form can be downloaded from the Brooks website
www.brooksinstrument.com or is available from any Brooks Instrument
location listed above. This is required before any Brooks Personnel can
begin processing. Copies of the form can be obtained from any Brooks
Instrument location listed above. Provide a Material Safety Data Sheet
(MSDS) for the fluid(s) used in the instrument.

2-5 Transit Precautions

To safeguard against damage during transit, transport the instrument to the
installation site in the same container used for transportation from the
factory if circumstances permit.

2-6 Removal from Storage

Upon removal from storage, a visual inspection should be conducted to
verify the condition of the equipment is “as received.”  If the equipment has
been in storage in conditions in excess of those recommended  (See
Section 2-3), the device should be subjected to a pneumatic pressure test
in accordance with applicable vessel codes. To maintain the ultra-clean
integrity, this service should be performed by the factory or one of the
authorized service centers.

Summary of Contents for SLA7840









































Reviews: