BRONKHORST BRIGHT Instruction Manual Download

Page: 36 / 39

8 | TROUBLESHOOTING

9.17.048

Page 36

8 Troubleshooting

No output signal

•

No power supply

Check power supply

•

PCB failure

Check cable

Return to factory

•

Valve blocked

Clean valve (qualified personnel only)

•

Filter or screen blocked

Clean filter or screen

•

Sensor failure

Return instrument to factory

Maximum output signal

•

PCB failure

Return instrument to factory

•

Sensor failure

Return instrument to factory

High setpoint vs. output offset

•

PCB failure

Return instrument to factory

•

Valve blocked

Clean valve (qualified personnel only)

•

Stoppage

Remove cause

•

Pressure not correct

Check pressure

Signal lower than expected

•

System stoppage

Remove cause

Flow is gradually decreasing

•

(Gas) Condensation

Decrease supply pressure or increase

temperature

•

Valve adjustment has changed

Check valve adjustment

•

Controller adjustment wrong

Check controller setting

Oscillation

•

Input pressure wrong

Adjust pressure

•

Valve damaged

Check valve

•

Volume / tubing between controller and

pressure controller too small/ short

Improve situation

•

Wrong controller settings

Check controller settings

Small flow occurs when valve

is supposed to be closed

•

Valve is leaking

Check valve

Parameter not available

•

Parameter is not supported by the

connected instrument.

Setpoint is neglected

•

Instrument has wrong controller mode

Set controller mode to ‘digital input’

•

Alarm- or counter limit reached

Reset alarm

Settings menu not accessible

•

Security mode ‘blocked’ or ‘menu’

Change security mode

Before switching on power, check if all connections have been made according to the hook-up diagram. The

hook-up diagrams are available at the download section of our website:

http://www.bronkhorst.com

LED indications can be very useful in case of problems with the instrument. See the “MANUAL INTERFACE:

micro-switch and LED’s” section in the manual “Operation instructions digital instruments (document nr.

9.17.023)”. This manual is available at the download section of our website:

http://www.bronkhorst.com

Contact Bronkhorst® local sales representative or send e-mail describing your problem to:

[email protected]

Summary of Contents for BRIGHT








































Search results

Summary of Contents for BRIGHT

Reviews:

Related manuals for BRIGHT

Brands by name

Popular brands

BRONKHORST BRIGHT, Instruction Manual

Search results

Summary of Contents for BRIGHT

Reviews:

Related manuals for BRIGHT

Brands by name

Popular brands