BRONKHORST BRIGHT Instruction Manual Download

Page: 34 / 39

7 | SECURITY SETTINGS

9.17.048

Page 34

The





signs in the upper right corner indicates that you

can scroll this menu using the and buttons to select

more items. The accessibility of following items can be set:

item

accessibility

edit setpoint

edit mode of the setpoint in

both custom readout 1 and 2

reset counter

counter reset in custom

readout 2.

reset alarm

alarm reset displayed in custom

readout 2.

select instrument

selecting another instrument

on the flowbus.

settings menu

advanced

advanced submenu in the

settings menu

7.4 Change Password

To change the password, select the option ‘new

password’ and press

This will open the ‘new password’ input display. Press

again to enter the new password edit mode.

You can enter a maximum of 8 characters. For less

characters, press

till the end of the edit field.

After changing the password press to select ‘confirm’.

Then press

Now the new password is stored and should be used to

enter the password protected items.
Press any key to return to security settings screen.

SET

Summary of Contents for BRIGHT








































Search results

Summary of Contents for BRIGHT

Reviews:

Related manuals for BRIGHT

Brands by name

Popular brands

BRONKHORST BRIGHT, Instruction Manual

Search results

Summary of Contents for BRIGHT

Reviews:

Related manuals for BRIGHT

Brands by name

Popular brands