BRONKHORST BRIGHT Instruction Manual Download | Manualshive

Page: 32 / 39

background image

6 | SETTINGS MENU

9.17.048

Page 32

Press

to start the sensor auto zero procedure.

While the auto zero procedure is active, the BRIGHT will

show the message ‘busy’. When finished, ‘auto zero

ready’.
Press any key to return to settings menu.

6.28 Restore instrument settings

To start the instrument restore procedure, select the

restore option from the advanced menu and press

to

enter.
Press to select the ‘start restore’ option.

Press

to start the instrument restore procedure.

While the restore procedure is active, the BRIGHT will

show the message ‘busy’. When finished, ‘auto restore

ready’.
Press any key to return to settings menu.

SET

SET

SET

«
...
30
31
32
33
34
...
»

Summary of Contents for BRIGHT








































Reviews:

No comments

Related manuals for BRIGHT

Brand: Keithley Pages: 73

Brand: Omicron Pages: 80

Brand: Parkside Pages: 114

Brand: Vega Pages: 20

Brand: Vega Pages: 16

Brand: Vega Pages: 2

Brand: Keysight Pages: 92

Brand: Kobold Pages: 55

Brand: Motortech Pages: 142

Brand: Conrad Electronic Pages: 38

Brand: WATERGUARD Pages: 2

Brand: Neogen Pages: 9

Brand: X-Rite Pages: 130

Brand: Saluki Technology Pages: 161

Brand: Xsens Pages: 12

Brand: Falcon Pages: 25

Brand: BART Pages: 24

Brand: Saab Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands