background image

4

www.bromicheating.com

IMPORTANT NOTES AND WARNINGS

WARNING

Failure to follow the warnings and instructions in this manual could 
result in severe personal injury, death or property damage.  

• 

Installation and repair should be done by a qualified service 
person. The heater should be inspected before use and at 
least annually by a qualified service person.

• 

Do not use or store flammable materials near this appliance

• 

Do not spray aerosols or flammable materials in the vacinity of 
this appliance while it is in operation 

• 

Any guard or other protective device removed for servicing 
(conducted by an authorised person) must be replaced before 
operating the heater.

• 

Children and adults should be alerted to the hazards of high 
surface temperatures and should stay away to avoid burns or 
clothing ignition.

• 

Children should be carefully supervised when they are in the 
area of the heater.

• 

Clothing or other flammable materials should not be hung 
from the heater or placed on or near the heater.

• 

Do not perform maintenance until heater has been turned off, 
and heater temperature has cooled to room temperature.

• 

Do not expose the burner to water or moisture. The appliance 
must be protected from rain.

• 

Do not use the heater if any of these parts are exposed 
to water until the appliance is inspected or repaired by an 
authorised service person.

• 

The installer is to ensure that the requirements of the local 
authority, local gas fitting regulations, municipal building 
codes, and any other relevant statutory regulations are carried 
out.

• 

Certain materials or items, when stored under or near the 
appliance, will be subjected to radiant heat and could be 
seriously damaged. 

• 

The whole gas system, hose assembly, regulator, pipes, and 
burner should be inspected for damage and leaks before each 
use and at least annually by an authorized person for the life 
of the heater.

• 

The hose assembly must be replaced prior to the appliance 
being put into operation if there is evidence of excessive 
abrasion or wear, or if the hose is damaged. The replacement 
hose must be purchased from Bromic Heating Pty Ltd.

• 

All leak tests should be done with a soap solution. Never use 
an open flame to check for leaks.

• 

Do not use the heater until all connections have been leak 
tested by an authorised person.

• 

This radiant heater is NOT intended to be installed on 
recreational vehicles and/or boats.

• 

Improper installation, adjustment, or alteration can cause 
personal injury, property damage, or even death.

• 

Do not attempt to alter the unit in any manner.

• 

Do not paint any surface of the heater or top canopy reflector.

• 

Burner and circulation air passageways of the heater must be 
kept clean. Frequent cleaning may be required as necessary.

• 

Turn Gas Supply off when not in use.

• 

Check the heater immediately if any of the following occurs:

 

»

The heater does not reach temperature.

 

»

The burner makes popping noise during use (a 
slight noise is normal when the burner is ignited or 
extinguished). 

• 

This appliance is not intended for use by young or infirm 
persons unless they have been adequately supervised by a 

responsible person to ensure that they can use the appliance 
safely. 

• 

Check for damage to the appliance regularly. If damage to 
the appliance is suspected, discontinue use immediately and 
contact the supplier or qualified person for repair. 

• 

Avoid inhaling fumes emitted from the heater’s first 
use. Smoke and odour from the burning of oils used in 
manufacturing will appear. Both the smoke and odour will 
dissipate after approximately 30 minutes. 

• 

The pressure regulator and hose assembly supplied with the

        appliance must be used. Replacement regulator and hose     
        assemblies must be purchased from Bromic Heating Pty Ltd. 

• 

Storage of an appliance indoors is permissible only if the 
cylinder is disconnected and removed from the appliance. 

• 

A cylinder must be stored outdoors in a well-ventilated area 
out of the reach of children. A disconnected cylinder must 
have dust caps tightly installed and must not be stored in a 
building, garage or any other enclosed area. 

• 

Do not store a spare LP-gas cylinder under or near this 
appliance; 

• 

Never fill the cylinder beyond 80%  full

!

Summary of Contents for Tungsten Smart-Heat



























Reviews: