Bromic Heating Tungsten Smart-Heat Installation, Instruction And Service Manual Download Page 13 | Manualshive

Page: 13 / 26

background image

13

www.bromicheating.com

INSTALLATION INSTRUCTIONS

CONTINUED...

STEP 6:

Slide top arms over front assembly slip joints - Ensure top screw holes are faced inwards.

Secure the front panel to top arms using 4 x M5 screws and supplied M5 Hex Key.

STEP 7:

Secure the top arms to lower arm slip joint using 2 x M8 x45 screws and supplied M8 Hex Key.

* Note: The joint between the lower and upper arms is firm to

ensure` rigidily and stability of the product. To engage slowly lever

the two sections together using some force and push down fully

L

R

«
...
11
12
13
14
15
...
»

Summary of Contents for Tungsten Smart-Heat



























Reviews:

No comments

Related manuals for Tungsten Smart-Heat

Brand: ZETRON Pages: 3

Brand: 2gig Technologies Pages: 4

Brand: 2gig Technologies Pages: 2

Brand: G1SLE Pages: 2

Brand: Campbell Pages: 3

Brand: Hanwell Pages: 34

Brand: HANSONG Pages: 11

Brand: Datapath Pages: 12

Brand: Hansen Pages: 4

Brand: Eaton Pages: 96

Brand: IBA Pages: 29

Brand: Jäger Pages: 18

Brand: GBD Pages: 60

Brand: SOMFY Pages: 112

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands