background image

22

bromic.com/heat

POST-INSTALLATION REPORT

Customer Business Name:

Date:    

dd

    /    

mm

    /    

yyyy

           

Site Address:

Suburb:

State:                                   Postcode:

Customer Contact Details:

Name:

Position:

Ph: (       )                                        Fax: (       )  

Mobile:

Installer Contact Details:

Name:

Position:

Ph: (       )                                        Fax: (       )  

Mobile:

POST-INSTALLATION REPORT

FOR PLATINUM GAS RADIANT HEATERS

AFTER HEATER INSTALLATION PLEASE PHOTOCOPY, COMPLETE, & SEND THIS REPORT 

BY: 

Please fill in the relevant information or circle the 

appropriate Yes/No responses below:

How many Platinum heaters are 

installed on this site?

3-Tile: 

________

5-Tile: 

________

What type of gas is used?

LPG

Natural 

Gas

Is/Are the heater(s) exposed to 

salt air or any other corrosive or 

chemical atmosphere?

Yes

No

Does the heater(s’) installation 

location pose a hazard to the 

site?

Yes

No

Do heater clearances match the 

minimum requirements outlined 

in the “Installation Requirements” 

section of the 

Installation, 

Operation and Service Manual

?

Yes

No

Is the gas supply line adequately 

sized for the number of heaters 

installed?

Yes

No

Have gas lines been purged of 

air?

Yes

No

Have gas lines been checked 

for leaks with a soapy water 

solution?

Yes

No

Was the heater field tested and 

operated without malfunction?

Yes

No

What is the 

inlet

 gas supply 

pressure?

_________  kPa

What is the gas valve 

outlet

 

pressure (at test point)?

_________  kPa

Signature of authorised person:

Name:

Company:                                                                                           Position:

Date:       

dd

    /    

mm

    /    

yyyy

          

Summary of Contents for PLATINUM 300 SMART-HEAT



























Reviews: