Broadcom Brocade G720 Hardware Installation Manual Download Page 63

Page: 63 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Power Supply and Fan Assembly

Power Supply and Fan Assembly Overview

The Brocade G720 chassis has two 350W power supply and fan assemblies. The power supply and fan assembly units

can be removed and replaced without special tools. The device can continue operating during the replacement.

Figure 28: AC Power Supply and Fan Assembly

1. AC Power Cable Receptacle

2. Power Supply and Fan Assembly Status LED

3. Power-On/Off Switch

4. Power Supply and Fan Assembly Handle

5. Captive Screw
The device supports the following types of power supplies. (DC power is not supported.)

•

AC power supply with nonport-side air exhaust. This unit moves the air from the port side to the nonport side of the

device.

•

AC power supply with nonport-side air intake. This unit moves the air from the nonport side to the port side of the

device.

NOTE

The two power supply and fan assemblies that are concurrently installed in the chassis must be of the same

power type, model (airflow direction), and part number. If the airflow directions are different, an error is

generated on the console.

NOTE

The power supply and fan assembly units are hot-swappable if they are replaced one at a time. They are

identical and fit into either slot.

NOTE

The device can operate all the ports with one power supply and fan assembly unit if you do not require

redundancy.

The device fans are fixed inside the combined power supply and fan assemblies to provide necessary airflow to cool the

whole system. The fans operate at three speeds: low, normal, and high. The system software sets the fan speed and

measures it through the tachometer interface.

G720-Install-IG101

Broadcom

Summary of Contents for Brocade G720























































































Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands

Broadcom Brocade G720, Hardware Installation Manual

Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands