Broadcom Brocade G720 Hardware Installation Manual Download Page 55

Page: 55 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

Modules webpage on www.broadcom.com. If you use an unqualified transceiver, the

switchshow

command output

shows the port in a Mod_Inv state. The issue is also logged in the system error log.
To insert an SFP+ transceiver, complete the following steps:

NOTE

The 32Gb/s and 64Gb/s SFP+ transceivers do not have bails. Always use the pull tab to insert or remove the

transceivers, since the transceiver might be hot.

1. Use the pull tab on the 32Gb/s and 64Gb/s SFP+ transceivers to help push the transceiver into the port.

Transceivers are keyed so that they can be inserted only with the correct orientation. If a transceiver does not slide

in easily, ensure that it is correctly oriented. Push the transceiver into the port until it is firmly seated and the latching

mechanism clicks.

NOTE

Each SFP+ transceiver has a 10-pad gold-plated PCB-edge connector on the bottom. The correct position

to insert an SFP+ transceiver into an upper row of ports is with the gold edge down. The correct position to

insert an SFP+ transceiver into a lower row of ports is with the gold edge up.

Figure 24: Installing an SFP+ Transceiver into a Port

1. Pull Tab

2. SFP+ Cable

3. SFP+ Transceiver

2. Position a cable so that the key (the ridge on one side of the cable connector) is aligned with the slot in the transceiver.

Insert the cable into the transceiver until the latching mechanism clicks.

NOTE

Cables are keyed so that they can be inserted in only one way. If a cable does not slide in easily, ensure that

it is correctly oriented. Do not insert any unsupported cable intended for another type of transceiver into a

regular SFP+ transceiver. You may damage the cable as well as the transceiver.

Replacing an SFP+ Transceiver

To remove an SFP+ transceiver and then install a new SFP+ transceiver, complete the following steps.

NOTE

Replacing an SFP+ transceiver may cause disruption in the fabric or to the attached device.

G720-Install-IG101

Broadcom

Summary of Contents for Brocade G720























































































Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands

Broadcom Brocade G720, Hardware Installation Manual

Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands