Broadcom Brocade G720 Hardware Installation Manual Download Page 56

Page: 56 / 86

G720-Install-IG101 Installation Guide

Brocade

G720 Switch Hardware Installation Guide

NOTE

32Gb/s and 64Gb/s SFP+ transceivers have pull tabs instead of bails. Always use the pull tab to insert or

remove the SFP+ transceivers, since the transceiver might be hot.

1. Remove any cables that are inserted into the transceiver.
2. Grasp the SFP+ transceiver pull tab and pull the tab straight out.

NOTE

Grasp the tab near the body of the transceiver to reduce the chances of bending the pull tab. Avoid touching

the transceiver because it may be hot.

3. To insert the replacement transceiver, use the pull tab on the SFP+ transceiver to carefully push the transceiver into

the port.
Transceivers are keyed so that they can be inserted only with the correct orientation. If a transceiver does not slide in

easily, ensure that it is correctly oriented.

NOTE

Each SFP+ transceiver has a 10-pad gold-plated PCB-edge connector on the bottom. The correct position

to insert an SFP+ transceiver into the upper row of ports is with the gold edge down. The correct position to

insert an SFP+ transceiver into the lower row of ports is with the gold edge up.

Figure 25: Replacing an SFP+ Optical Transceiver in an Upper Port

1. Pull Tab

2. SFP+ Cable

3. SFP+ Transceiver

G720-Install-IG101

Broadcom

Summary of Contents for Brocade G720























































































Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands

Broadcom Brocade G720, Hardware Installation Manual

Search results

Summary of Contents for Brocade G720

Reviews:

Related manuals for Brocade G720

Brands by name

Popular brands