background image

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

360.854.9479 

9

TS-6 Installation and Operation Manual

INSTALLATION

Terminal J7

8 - Connect the “Program on Hold” feed to the “MOH” terminals on J7.
9 - Set DIP switches according to the required operation, see chart below:

DIP switch settings on the Controller unit:  Firmware Version 1.08 or greater.

DIP – 1

CPC and current monitoring is turned off.  This allows for operation

of the unit without any phone lines plugged in.
DIP – 2

Two Hybrid operation.  The Hybrid and OPT relays control Hybrid

1, while the DLY and REC relays control Hybrid 2
DIP – 3

Auto-Answer.  If this is on the lines will auto answer and be placed

on hold.  This setting supercedes DIP-4.
DIP – 4

Re-defines the Flash button/LED as Auto-Answer on/off.  DIP-3

must be off for this to work.
DIP – 5

Hot line 5, unaffected by Busy Button.

DIP – 6

Hot line 6, unaffected by Busy Button.

DIP – 7

Hybrid 1 control.  OFF = Latch mode, ON = Pulse mode using

Hybrid and OPT.
DIP - 8Hybrid 2 control.  OFF = Latch mode, ON = Pulse mode using DLY and
REC relays.

DIP switch settings on the Switch Console:

DIP – 1-2

Address selection for remote Switch Consoles.  Each Switch Console

must have a different address:  00, 01, 10 or 11.  If two or more are the same there
will be data collisions and the system will not function properly.
DIP – 3

Turns off Ringer.  The ringer can be turned down with the volume

control but there will still be a low audible ring, which could be distracting to the
on-air talent.  This setting turns it off in software.
DIP – 4-7

Not used

DIP – 8

Test mode.  Used to test LED’s and pushbuttons on the Switch

Console.

10 - Connect the supplied 16vac @ 600ma wall transformer to J17, the power
connector on the TS-6 Controller.  

NOTE:  The Controller supplies power for all Switch Consoles.

11 - Follow the System operation guide below.

1

2

3

4

5

6

7

8

9

10

11

12

MOH

In-

MOH

In+

Shld

N.C.

COM

N.O.

N.C.

COM

N.O.

N.C.

COM

N.O.

N.O.

Com

N.C.

Dly

In

Gnd

Dly

In +

Dly

TTL

REC

In

Gnd

REC

In +

REC

TTL

OPT

In

Gnd

Opt

In +

Opt

TTL

13

14

15

16

17

18

19

20

21

22

23

24

------------------

REC

--------------

---------- HYBRID ----------      ------------- OPT --------------       ------------ DLY ------------

Summary of Contents for TeleSwitch Six
















Reviews: