Britax ISOFIX COMPATIBLE Instruction Manual Download

Page: 45 / 92

Instructions for Installation & Use

REMOVING CHILD SEAT FROM

VEHICLE:

Step 1.

Press top tether adjuster button and

Step 2 .

Lengthen top tether strap fully.

Step 3.

Disconnect top tether attachment clip

from vehicle anchorage fitting.

Step 4.

Disengage the vehicle seatbelt buckle.

Step 5.

Remove infant insert (if fitted).

IMPORTANT -

Ensure buckle tongues are

placed into buckle tongue holders.

Step 6.

Lift out middle cover.

Step 7.

Remove vehicle seatbelt from blue

REARWARD FACING BELT PATH.

Step 8.

Press the blue release rebound bar

button to unlock the rebound bar.
Store the rebound bar away.

Step 9.

Re-attach the flap at the front of the

child seat.

SETUP -

REMOVE CHILD SEAT FROM VEHICLE

FOR

REARWARD FACING SEATBELT

Press

Pull

Lengthen strap

Press

Please ensure you have followed the step 1 on page 44.

Summary of Contents for ISOFIX COMPATIBLE





























































































Search results

Summary of Contents for ISOFIX COMPATIBLE

Reviews:

Related manuals for ISOFIX COMPATIBLE

Brands by name

Popular brands

Britax ISOFIX COMPATIBLE, Instruction Manual

Search results

Summary of Contents for ISOFIX COMPATIBLE

Reviews:

Related manuals for ISOFIX COMPATIBLE

Brands by name

Popular brands