Britax ISOFIX COMPATIBLE Instruction Manual Download Page 3

Page: 3 / 92

Instructions for Installation & Use

CHILD SEAT FEATURES -

FORWARD FACING

SET UP

• GENERAL INFORMATION

• FORWARD FACING RECLINE POSITIONS

• INSTALLING INTO YOUR VEHICLE

• SEATBELT FOR FORWARD FACING

• ISOFLEX

FOR FORWARD FACING

• TOP TETHER FOR FORWARD FACING

• OPEN ADVANCED SIDE IMPACT CUSHION TECHNOLOGY

• HEADREST AND SHOULDER HARNESS

• REMOVE CHILD FROM CHILD SEAT

• CLOSE ADVANCED SIDE IMPACT CUSHION TECHNOLOGY

• REMOVE CHILD SEAT FROM VEHICLE SEATBELT

• REMOVE CHILD SEAT FROM VEHICLE ISOFLEX

FORWARD FACING

CARE & MAINTENANCE

CONTENTS

CARE

AND

MAINTENANCE

• CLEAN

HARNESS

BUCKLE

• REMOVE

COVER

• REPLACE

COVER

ACCESSORIES

INSTALLATION OF VEHICLE UPPER ANCHOR POINT

IN CASE OF ACCIDENT

WARRANTY

Scan QR code

for forward

facing seatbelt

installation video.

Scan QR code

for forward

facing ISOFLEX

installation video.

Summary of Contents for ISOFIX COMPATIBLE





























































































Search results

Summary of Contents for ISOFIX COMPATIBLE

Reviews:

Brands by name

Popular brands

Britax ISOFIX COMPATIBLE, Instruction Manual

Search results

Summary of Contents for ISOFIX COMPATIBLE

Reviews:

Brands by name

Popular brands