background image

L-1643BH-H

Page  3

================================================================================================

SAFETY

•  Do not exceed maximum towing capacity of towing vehicle.
•  Do  not  exceed  the  maximum  drawbar  pull  rating  of  the  towing 

vehicle.  Drawbar  pull  is  the  horizontal  force  required  to  pull  the 

attachment (including weight of load).  

•  Only tow this product in the vehicle’s tow mode/  speed setting or 

less than 5 mph. Do not exceed 5 mph.

•  Towing speed should always be slow enough to maintain control. 

Travel  slowly  and  use  caution  when  traveling  over  rough  terrain. 

Avoid holes, rocks and roots. 

•  Slow down before you turn and do not turn sharply. 
•  Use wide turning angles to ensure the attachment follows the path 

of the towing vehicle.

•  Do not use attachment on steep slopes. A heavy load could cause 

loss of control or overturn attachment and towing vehicle.  Additional 

weights may need to be added to your vehicle; check with towing 

vehicle manufacturer for recommendations.

•  Reduce towed weight when operating on slopes.
•  Keep  all  movement  on  slopes  slow  and  gradual.  Do  not  make 

sudden changes in speed, directions, or   turning.

•  If you start and stop suddenly on hills, you may lose steering control 

or the towing vehicle may tip.  Do not start or stop suddenly when 

going uphill or downhill. Avoid uphill starts.

•  Slow  down  and  use  extra  care  on  hillsides.  Turf  conditions  can 

affect  vehicle  stability.  Use  extreme  caution  while  operating  near 

drop-offs.

•  Do not drive close to creeks, ditches and public highways.
•  Watch out for traffic when crossing near roadways. 
•  Use care when loading or unloading the vehicle into a trailer or truck.
•  The attachment can obstruct the view to the rear. Use extra care 

when operating in reverse.

•  When reversing, carefully back-up straight to avoid jackknifing. Do 

not  allow  towing  vehicle  wheels  to  contact  attachment  draw  bar. 

Damage could result.

•  Stop on level ground, disengage drives, set the parking brake, and 

shut off engine before leaving the operator’s position for any reason 

including  emptying the attachment. 

•  Use this attachment for intended purpose only.
•  This attachment is intended for use in lawn care & home applications. 

 

Do  not  tow  behind  a  vehicle  on  a  highway  or  in  any  high  speed 

applications.  Do  not  tow  at  speeds  higher  than  the  maximum  

recommend towing speed.

•  Do not tow this product behind a motor vehicle such as a car or 

truck.

•  Always wear substantial footwear. Do not wear loose fitting clothing 

that can get caught in moving parts.

•  Keep your eyes and mind on your towing vehicle, attachment and 

area being covered. Do not let other interests distract you.

•  Stay alert for holes and other hidden hazards in the terrain
•  Keep the towing vehicle and attachment in good operating condition 

and keep safety devices in place.

•  The towing vehicle and attachment should be stopped and inspected 

for damage after striking a foreign object. Any damage should be 

repaired before restarting and operating the equipment.

•  Keep all parts in good condition and properly installed. Fix damaged 

parts immediately. Replace worn or broken parts. Replace all worn 

or damaged safety and instruction decals. Keep all nuts, bolts and 

screws tight.

•  Do not modify the attachment or safety devices. Unauthorized 

modifications to the towing vehicle or attachment may impair its 

function, safety and void the warranty.

TOWING VEHICLE AND TOWING SAFELY

•  Know your towing vehicle controls and how to stop safely. READ 

YOUR TOWING VEHICLE OWNER’S MANUAL before operating.

•  Check the towing vehicle brake action before you operate. Adjust or 

service brakes as necessary.

•  Stopping distance increases with speed and weight of towed load. 

Travel slowly and allow extra time and distance to stop.

•  Use only approved hitches. Tow this attachment only with a towing 

vehicle that has a hitch designed for towing. Do not connect this 

attachment except at the approved hitch point.

•  Follow the tow vehicle manufacture’s recommendations for weight 

limits for towed equipment & towing on slopes. Use counterweights 

or  wheel  weights  as  described  in  the  towing  vehicle  operator’s 

manual.

•  Do not shift to neutral and coast downhill.
•  Do not allow children to operate the towing vehicle. Do not allow 

adults  to  operate  the  towing  vehicle  without  proper  instruction  or 

without having read the owner’s manual.

PROTECT THOSE AROUND YOU

•  Before you operate any feature of this attachment or towing vehicle, 

observe your surroundings and look for bystanders.

•  Keep children, bystanders and pets at a safe distance away while 

operating this or any attachment.

•  Use care when reversing. Before you back up, look carefully behind 

for bystanders.

KEEP RIDERS OFF TOWED  

ATTACHMENT AND TOWING VEHICLE

•  Do not carry passengers.
•  Do not let anyone, especially children, ride in/on this attachment, the 

towing vehicle or hitch bracket. Riders are subject to injury such as 

being struck by foreign object and/or being thrown off during sudden 

starts, stops and turns. Riders may also obstruct the operator’s view 

resulting in this attachment being operated in an unsafe manner.

Summary of Contents for SATY-40 BH





































Reviews: