Brink Air Comfort Installation Regulations Download Page 3

Installation regulations

Air Comfort

Store near the appliance

This appliance may be used by children as of 8 years of age, persons with reduced
physical or mental capacities, and persons with limited knowledge and experience if
they are supervised or have received instructions on how to use the appliance safely
and are aware of the possible dangers.
Children younger than 3 years of age must be kept away from the appliance, unless
they are under constant supervision.
Children between the ages of 3 and 8 may only switch the appliance on or off, but only if
supervised or if they have received clear instructions on the safe use of the appliance
and understand the possible dangers, on the condition that the appliance has been
placed and installed in the normal position for use. Children between the ages of 3 and
8 may not insert the plug into the socket, nor clean or make changes to the settings of
the appliance, nor carry out any maintenance on the appliance that would normally be
carried out by the user. Children may not play with the appliance.

If you need a new power cable, always order the replacement from Brink Climate

Systems B.V. To prevent dangerous situations, a damaged mains connection must only

be replaced by a qualified expert!

Country: GB

Summary of Contents for Air Comfort



















































Reviews: