Briggs & Stratton IS3200Z Series Dealer Setup & Adjustment Instructions Manual Download Page 2

Page: 2 / 24

Not for

Reproduction

ferrismowers.com

Quick Setup List

Setup Procedures

Uncrate the unit.

Connect the battery cables.

Install the ground speed control levers.

Install the seat.

Assemble the roll bar retainer pins.

Install the roll bar on the unit.

Install the roll bar safety decals (export models only).

Check engine oil level.

Check / Fill transmission oil level.

Check tire pressures.

Check mower blade bolt torque.

Install the mower deck pusher bars (72" Export Mower Decks)

Install the mower deck (72" Export Mower Decks)

Install the discharge chute (72" Export Mower Decks)

Install the mower deck drive belt (72" Export Mower Decks)

Check the deck lift rod timing.

Check and level the mower deck.

Check the mower deck drive belt.

Lubricate all grease and oil points.

Check / Add fuel.

Start the engine

PERFORM THE SAFETY CHECKS

Check for LOOSE HARDWARE.

Check all OPERATOR CONTROLS.

Perform SAFETY INTERLOCK SYSTEM CHECK.

Register Product

To register the product: log onto www.thepowerportal.com, select the appropriate brand, click “Sales &

Marketing”, select the “Product Registration” link, and then select “New Product Registration”. Fill out and submit

the online product registration form.

Ferris is a registered trademark of Briggs & Stratton

Corporation.

Summary of Contents for IS3200Z Series

























Search results

Summary of Contents for IS3200Z Series

Reviews:

Related manuals for IS3200Z Series

Brands by name

Popular brands

Briggs & Stratton IS3200Z Series, Dealer Setup & Adjustment Instructions Manual

Search results

Summary of Contents for IS3200Z Series

Reviews:

Related manuals for IS3200Z Series

Brands by name

Popular brands