background image

Not for 

Reproduction

11

height adjustment pin in the 3” (7.6 cm) position to hold in

place.

3. Block up the mower deck until all hanger chains are

slack.

4. To adjust the inner lift rod (A, Figure 23): Loosen the

jam nut (B) on the front ball joint (C) then remove the

1/2” hardware (D) fastening the ball joint to the lift

pivot arm. Turn the ball joint 

clockwise

 to shorten the

distance between the rod pivots or 

counter-clockwise

 to

lengthen the distance between the rod pivots. Reinstall

the ball joint on the lift pivot arm and secure with the

1/2” hardware previously removed. Tighten the jam nut

against the lift rod.

23

5. To adjust the outer lift rod (E): Loosen the jam nut (F) on

the front ball joint (G) then remove the 1/2” hardware (H)

fastening the ball joint to the lift pivot arm. Turn the ball

joint 

clockwise

 to shorten the distance between the rod

pivots or 

counter-clockwise

 to lengthen the distance

between the rod pivots. Reinstall the ball joint on the lift

pivot arm and secure with the 1/2” hardware previously

removed. Tighten the jam nut against the lift rod.

6. Remove blocks from under the mower deck.
7. Remove the cutting height adjustment pin from in front

of the deck lift pedal arm. Lift mower deck and reinstall

adjustment pin in desired mowing height.

Deck Leveling Adjustment

Before adjusting the deck level, the deck lift rod timing must

be checked and/or adjusted.

Determining if the Deck Leveling Needs to be

Adjusted

1. Park the unit on a flat, level surface. Disengage the PTO,

engage the parking brake, turn the ignition switch to OFF,

and remove the ignition key. 

2. Lock the deck lift pedal in the TRANSPORT position.

Place the cutting height adjustment pin in the 4" position

and lower the deck lift pedal until the deck lift arm

contacts the cutting height adjustment pin. 

3. Verify that the tires are inflated to the correct pressure. 
4. Verify that the mower blades are flat, and not bent or

broken. A bent or broken blade must be replaced. 

 WARNING

 

Avoid Injury! Mower blades are sharp.

Always wear gloves when handling blades or working near

blades. 

5. See Figure 24. Position the outside mower blades so they

face front-to-back. 

24

6. Measure the front tip (A, Figure 24) of the blade from the

cutting edge to the ground. 

7. Measure the rear tip (A) of the blade from the cutting

edge to the ground. 

8. Repeat the process on the other side of the machine. 

•  the front measurements should equal 4" (10,2 cm). 
• the rear measurements should equal 4-1/4" (10,8

cm) 

If the measurements do not equal the measurements as

listed above, adjust the deck leveling. 

Deck Leveling Procedure

1. Place the deck height adjustment pin in the 4" (10,2 cm)

position.

2. Loosen the jam nut (A, Figure 25) on the deck linkages

(B).

Summary of Contents for IS3200Z Series

























Reviews: