Not for
Reproduction
41
Setting Exercise Timer
The generator is equipped with an exercise timer.
During the exercise period, the unit runs for
approximately 20 minutes and then shuts down.
Electrical load transfer DOES NOT occur during the
exercise cycle (unless an utility power outage occurs).
The generator will only enter the exercise cycle if the
unit is in the AUTO mode and this exact procedure is
followed.
To set the exercise timer:
NOTICE
The generator is set with a service code
exercise cycle setting of Tuesday at 2:00 P.M, Central
Time. To change the cycle setting, proceed to the
following steps:
1. Choose the day and time you want your generator
to exercise.
2. Press and hold the left arrow and right arrow
simultaneously for 3 seconds to enter the General
Set-Up program mode. See General Set-Up flow
chart in Menu Section.
3. Verify and/or set the time and date on the unit.
4. Go to the SET EXERCISE prompt and hit the “OK”
button.
NOTICE
Items will flash until they are selected.
SELECT DAY: Use the left or right arrow to toggle
through the days of the week, Once the day is
selected, hit the “OK” button.
SELECT HOUR: Use the left or right arrow to
toggle through between 1 and 12. Choose the
hour of day you want the generator to exercise
then hit the “OK” button.
SELECT MINUTE: Use the left of right arrow to
toggle between :00 and :59. Choose the minute of
the day you want the generator to exercise then
hit the “OK” button.
SELECT AM/PM: Use the left of right arrow to
toggle between AM and PM. Once chosen, hit the
“OK” button.
NOTICE
During the weekly exercise cycle, the
generator will run for 20 minutes, but it will not supply
power to the home. During the exercise cycle, the in-
home monitor will continue blinking the GENERATOR
READY green LED.
If you want to change the day and time the unit
exercises, simply perform the procedure again.
To turn off the generator exercise cycle, go to the OFF
selection within the day of the week menu and press
OK. The display will then scroll: EXERCISE CYCLE
OFF.
Maintenance
Servicing the System
Before performing any generator maintenance, always
perform the following steps:
1. Set generator’s circuit breaker to its
OFF
position.
2. Press and hold the control board
OFF
button.
3. Remove 15 Amp fuse from control board.
4.
Utility voltage is present at generator control
board.
Disconnect power before servicing control
board by removing the fuses from the transfer
switch.
5. After all servicing has been completed, replace
fuses in transfer switch, replace 15 Amp fuse in
control board, set circuit breaker ON and press
and hold control board AUTO button.
Service Code Detection System
The generator may have to run for long periods of time
with no operator present. For that reason, the system
is equipped with sensors that automatically shut down
the generator in the event of potentially damaging
conditions, such as low oil pressure, high temperature,
over speed, and other conditions.
The generator’s control board shows service code
descriptions scrolling across the digital display. The
service code descriptions are listed below:
• Low Battery Voltage
• Low Oil Pressure
• Under Voltage
• Over Voltage
• Engine Does Not Start
• Low Frequency
• Engine Overspeed
• High Oil Temperature
• Transfer Switch Service code
• Battery Charge Circuit
Summary of Contents for Fortress
