manualshive.com logo in svg

Bridgeview BALE KING 7400, Operator'S Manual, Page: 5 / 102

Share
Download
Bridgeview BALE KING 7400 Operator'S Manual Download Page 5

Bridgeview Manufacturing Inc.

 

Page 1 

INTRODUCTION 

Thank  you  for  purchasing  a 

Bale  King 

bale  processor.    With  the  proper  operation  and  service  as 

outlined in this manual, the Bale King will provide you with years of trouble-free operation. 

 

This is a complete safety, operation and service manual for the Bale King 7400. The manual 

covers in detail how to safely and effectively use your new processor. The procedures outlined in this 

manual  should  be  followed  to  ensure  safe  operation  and  longevity  of  your  machine.  The  service 

manual covers all parts you may need to order in case of accident, breakdown, or normal wear. Please 

read completely through this manual before beginning operation of your new machine. 

Safety Precautions 

The following safety precautions MUST be followed to ensure safe operation of the Bale King 
bale processor. 

 

•

 

ALWAYS

 turn 

OFF

 the tractor when leaving the operating platform. 

 

•

 

DO NOT 

stand in front of the discharge chute while the machine is running. 

 

•

 

DO NOT 

walk or move under the bale forks when they are in the upward position, either 

loaded with a bale, or connected to a running tractor. 

 

•

 

DO NOT

 enter the machine while in operation, or while connected to a running tractor. 

 

•

 

DO NOT

 open the rotor access panel while the machine is connected to a running tractor. 

 

•

 

DO NOT

 clean machine while in operation. 

 

•

 

DO NOT

 stick any device into the machine to clear debris while the machine is in operation. 

 

•

 

ALWAYS 

turn off the tractor when cleaning the processor, removing twine, or hooking up 

/ unhooking the machine 

 

•

 

ALWAYS 

use safety chain when towing the machine on a highway. 

 

•

 

DO NOT 

operate if any part of the

 PTO safety shielding 

is missing or is not secured.  

 

 

Summary of Contents for BALE KING 7400







































































































Reviews:

No comments