manualshive.com logo in svg

Bridgeview BALE KING 7400, Operator'S Manual, Page: 36 / 102

Share
Download
Bridgeview BALE KING 7400 Operator'S Manual Download Page 36

Bridgeview Manufacturing Inc.

 

Page 32 

Cylinder Maintenance 

The  hydraulic  cylinders  are  easily  removed  for  repair  or 

maintenance simply by:  

•

 

Lowering  the  fork  (or  deflector)  to  the  down 

position and unhooking the hydraulic lines.  Be sure 

there is no pressure on the lines and mark the line 

locations so there is no confusion when reinstalling 

the cylinders.  Check hydraulic schematics. 

•

 

Removing the cotter pin closest to the frame of the 

machine and sliding the cylinder pins out 

•

 

To reinstall, reverse the removal procedure 

 

NOTE:  Always cover exposed cylinder shafts with grease to avoid rusting of shafts if the unit is 

not used for extended periods of time.  Rusted cylinder shafts are NOT covered by warranty 

 

NOTE:  Check  all  hoses  and  fittings  periodically  for  leaks.    Tighten  or  replace  any  dripping 

components or any worn out hoses. 

 

 

Summary of Contents for BALE KING 7400







































































































Reviews:

No comments