Bridgeview BALE KING 7400 Operator'S Manual Download Page 44

Page: 44 / 102

Bridgeview Manufacturing Inc.

Page 40

PARTS MANUAL

Machine Overview ................................................................................................................ 41

Jack and Hitch....................................................................................................................... 42

Wheels & Hub ...................................................................................................................... 43

Hub & Spindle .................................................................................................................. 44

Driveline ............................................................................................................................... 45

Driveline Guards ............................................................................................................... 46

Rotor ................................................................................................................................. 47

Rotor Gearbox ................................................................................................................... 48

Input Gearbox ................................................................................................................... 49

Gearbox Coupler Shaft ...................................................................................................... 50

PTO Shaft ......................................................................................................................... 51

Chain Table .......................................................................................................................... 52

Chain Table Overview....................................................................................................... 53

Chain & Slat Assembly ..................................................................................................... 54

Chain & Slat Front Panel ................................................................................................... 55

Chain & Slat Rear Panel .................................................................................................... 56

Chain & Slat Access Panel ................................................................................................ 57

Hoop Grates .......................................................................................................................... 58

Hoop Grates ...................................................................................................................... 59

Adjustment Handles .......................................................................................................... 60

Lower Tub Components ........................................................................................................ 62

Fine Chop Option .................................................................................................................. 64

Deflector ............................................................................................................................... 64

Lower Deflector ................................................................................................................ 64

Upper Tub Components ........................................................................................................ 68

Front Tub Components ......................................................................................................... 70

Hose Holder & Hydraulic Clamps ..................................................................................... 72

Diverter Control Box ......................................................................................................... 74

Rear Tub Components........................................................................................................... 76

Slow Moving Vehicle (SMV) Sign Kit .............................................................................. 77

Lights ................................................................................................................................ 78

Rear Fork .............................................................................................................................. 80

Three Bale Kit Option ........................................................................................................... 81

Three Bale Kit Left Arm ................................................................................................... 82

Three Bale Kit Right Arm ................................................................................................. 83

Three Bale Kit Center ....................................................................................................... 84

Back-up Camera Option ........................................................................................................ 85

Decals ................................................................................................................................... 86

HYDRAULIC SCHEMATICS ................................................................................................. 87

Summary of Contents for BALE KING 7400







































































































Search results

Summary of Contents for BALE KING 7400

Reviews:

Bridgeview BALE KING 7400, Operator'S Manual, Page: 44 / 102

Search results

Summary of Contents for BALE KING 7400

Reviews: