brewer Flex 5700 Installation & Operation Manual Download Page 3

Printed in USA © 2015 

Document # 2102861 RevA

Brewer

FLEX

Access

Exam Table

DANGER Indicates a hazardous 

situation that, if not avoided, will 

result in death or serious injury.

WARNING indicates a hazardous 

situation which, if not avoided, could 

result in death or serious injury.

CAUTION

 

indicates a hazardous 

situation which, if not avoided, could 

result in minor or moderate injury.

Safety Information

The primary concern of The Brewer Company is 

that the equipment is operated and maintained 

with the safety of the patient and healthcare staff 

in mind. To ensure safe and reliable operation:

  Read and understand all instructions in this 

manual before attempting to install or operate 

the unit.

  Ensure that appropriate personnel are 

informed on the  manual contents. This is the 

responsibility of the purchaser.

  Ensure that this manual is located near the 

table, or if possible, permanently affixed to the 

table.

SAFETY INFORMATION

COMPONENT IDENTIFICATION

Figure 1. Component Overview

Paper Roll Holder

Drawer Warmer Switch

(Models 5701, 5801 only)

Front Drawer

SafeGlide™

 

Slide-out Leg Support

Treatment Pan

(located under Leg Support Pad)

Foot Controls

Back Release Handle

(Models 5700/5701)

Pelvic Tilt Bar

(Models 5701, 5801 only)

 

Return 

To Chair

 Stop

Model 

5700/5701

STOP

RETURN

TO CHAIR

Model 

5800/5801

DANGER

WARNING

CAUTION

This is the safety alert symbol. It is used to 

alert you to potential physical injury hazards. 

Obey all safety messages that follow this 

symbol to avoid possible injury or death.

Summary of Contents for Flex 5700
























Reviews: