Breckwell BH32VF, Owner’S Instruction And Operation Manual

Page: 15 / 24

© 2021 Breckwell Hearth
15
LOG PLACEMENT
4. Install top left log (#4) on top of left bottom log.
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Right Top
Log #5
Rear Log
Support
Bracket
Left Log
Support
Bracket
Right Log
Support Bracket
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Right Top
Log #5
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Log #5
PILO
T
OFF
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Left Bottom
Log #2
Top Left
Log #4
Log #4
Back Log #1 Top Left
Log #4
Log Support
Bracket Studs
Burner Ports
Left Bottom
Log #2
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Log #5
Top Left
5. Install top right log (#5) on top of right bottom log.
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Right Top
Log #5
Rear Log
Support
Bracket
Left Log
Support
Bracket
Right Log
Support Bracket
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Right Top
Log #5
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Back Log #1
Top Left
Log #4
Right Top
Log #5
PILO
T
OFF
Log #5
PILO
T
OFF
PILO
T
OFF
Left Bottom
Log #2
Back Log #1
Left Bottom
Log #2
Top Left
Log #4
Log #4
Back Log #1 Top Left
Log #4
Log Support
Bracket Studs
Burner Ports
Left Bottom
Log #2
Right
Bottom
Log #3
Right
Bottom
Log #3
Right
Bottom
Log #3
Log #5
Top Left
CAUTION:
DURING INITIAL OPERATION OF THE NEW HEATER,
BURNING LOGS WILL GIVE OFF A PAPER BURNING SMELL
AND ORANGE FLAMES WILL BE PRESENT. SIMPLY OPEN
THE WINDOWS FOR A FEW HOURS TO VENT THE ODOR.
GLOWING WOOL PLACEMENT
Provided with your log set is a package of Glowing Embers
(rock wool). Break up the glowing wool into small dime
sized pieces or for a finer finish use a metal wire brush. Place
it over the small holes (ports) located on the burner pan.
Cover the entire section of holes (ports).*Replacement of
loose (Glowing Wool) must be purchased from the original
manufacturer and application of excess loose material may
adversely affect the performance of the heater. NOTE:
Wash your hands immediately after coming in contact with
wool material. In some cases the wool can cause slight
itching or burning, avoid any contact with eyes.
WARNING:
All previously applied loose material must be removed
prior to replacement. Do not cover the air channels with
the glowing wool.
FLAME APPEARANCE
Flames from the pilot, front and rear burner should be visually
checked as soon as the heater is installed. In addition,
periodically check the flames visually during operation.
PILOT FLAME
The pilot flame must always be present when the heater is
in operation. It should just touch the top of the thermocouple
tip for natural. Refer to the figure below for correct pilot
flame.
If the pilot flame does not touch the thermocouple, then the
burners cannot function reliably. Refer to the figure below
for incorrect shape of pilot flame.
MILLIVOLT CONTROL
Thermocouple
for Natural
Thermocouple
for LP
Thermocouple
for LP
Thermocouple
for Natural
PILO
T
OFF
Thermocouple
for Natural
Thermocouple
for LP
Thermocouple
for LP
Thermocouple
for Natural
PILO
T
OFF