background image

B - C r e a m   &   B - c r e a m   H D

36

ENGLISH

If one of these alarm codes appears on the display, please refer to Appendix 1: Possible Problems and their Solutions.

9  FIRMWARE VERSIONS CHRONOLOGY

Control display

Power board

AL03

Excessive motor absorption

Alarm displayed when the machine is operating in Service

Mode Service Mode or Super

AL04

Temperature probe damaged

This alarm stops the operation of the machine

AL05

Circuit board transmission error

This alarm stops the operation of the machine

AL06

Unplanned motor stop

Alarm displayed when the machine is operating in Service

Mode Service Mode or Super

AL07

24V power supply missing

This alarm stops the operation of the machine

AL08

Excess current, hardware protection intervention

Alarm displayed when the machine is operating in Service

Mode Service Mode or Super

AL09

Error Hall probes

This alarm stops the operation of the machine

AL10

Lack of communication between master and slave card 1 This alarm stops the operation of the machine

AL11

Lack of communication between master and slave card 2 This alarm stops the operation of the machine

AL12

Alarm low voltage motor

This alarm don’t stops the operation of the machine

AL13

System clock out of order

System clock out of order. The machine can work but the de-

frost timer can’t be used.

AL14

Clock battery out of order

Clock battery expired or out of order. The machine can work

but current time is reset when the machine is powered off.

Version

Notes

0.22

First production version.

0.23

Updates 2013.

1.01

Updates 2014.

First produtcion version with LCD display.

1.08

Updates 2015. 

Version

Notes

0.06

First production version.

0.10

Updates 2013.

0.27

Updates 2014.

Compatible version with new LCD display.

0.35

Updates 2015.

Summary of Contents for B-cream HD 1

























Reviews: