Branson F36h Operator'S Manual Download Page 46

Page: 46 / 132

Branson F36R(H)/F42R(H)

CAUTIONS FOR DECAl mAINTENANCE

Safety decals are attached to the

tractor for safe operation. Make sure

to follow the instruction on the decals

as well as the following instruction:

CAUTION

Keep the decals clean and intact.

If any decal is dirty, wash it with

soap and dry with a soft cloth.
Never use a solvent such a thin

ner or acetone, since it can ruin

the decals.
Do not spray high-pressure wa

ter directly onto the decal. The

decal may fall off the tractor.

•

ImPORTANT

If a decal is damaged or lost,

contact your local BRANSON

dealer immediately to install a

new decal.
Make sure to attach the decal

in the correct position cleanly

without bubbles after cleaning

its mounting surface.
If a decal is attached to a com

ponent to be replaced, replace

the decal as well.

•

K3트랙터-유럽향(Branson 36R,42R))-영문-036 36

2016-01-26 오후 2:20:19

Summary of Contents for F36h





































































































































Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands

Branson F36h, Operator'S Manual

Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands