Branson F36h Operator'S Manual Download Page 20

Page: 20 / 132

Branson F36R(H)/F42R(H)

연료가
새고 있어요

6640o122a

3 1

폭, 길이
강도는
여유를...

6640o123a

Fuel is

leaking!

Sufficient

Strength,

length and

width...!

실을때(후진)

내릴때(전진)

6640o124a

Loading

(backward)

Loading

(forward)

Inspect for fuel leaking;

Check the fuel lines and hos

es for damage or leakage

If this instruction is ignored,

there is a risk of fire.

•

WARNINg

Consider the strength, length

and width of loading ramps be

fore using;

Loading or unloading must be

done on a flat and safe place,

the tractor engine switched

off, and the parking brake en

gaged. The loading ramps

must be non-slip and have

sufficient strength, length, and

width for the tractor.

If this instruction is ignored, the

tractor may roll backwards or fall

off causing accident or injury.

•

WARNINg

Move the tractor backward when

loading, and forward when un

loading;

Move the tractor backward

when loading it on the truck,

and forward when unloading

from the truck.

If this instruction is ignored, the

tractor may roll or fall off caus

ing accident or Injury.

•

WARNINg

K3트랙터-유럽향(Branson 36R,42R))-영문-010 10

2016-01-26 오후 2:19:59

Summary of Contents for F36h





































































































































Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands

Branson F36h, Operator'S Manual

Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands