Branson F36h Operator'S Manual Download Page 81

Page: 81 / 132

OPERATION

Observe the guideline for towing

speed and capacity as below.
1. If the trailed weight is the same or

lighter than the tractor, maintain

the maximum speed of 26 km/h.

2. If the trailed weight is twice the

tractor or less, maintain the maxi-

mum speed of 13 km/h.

3. If the trailed weight is more than

twice the tractor, do not tow it.

4. Be careful especially when tow-

ing a load on a bad condition of

ground, slope or corner.

reDuCe SpeeD wHen tOwinG LOaD

6015O405A

HOw tO Drive

(1) Safety belt

(2) Seat sliding lever

CautiOn

The stopping distance be

comes longer on a down-

hill in proportion to the speed

and load weight. if the towed

weight is heavier than the trac-

tor and the braking system is

not installed on the trailer, re-

duce the speed. Observe the

guideline for towing speed

and capacity.

•

A42O507A

A42O508A

K3트랙터-유럽향(Branson 36R,42R))-영문-07 7

2016-01-27 오전 10:57:01

Summary of Contents for F36h





































































































































Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands

Branson F36h, Operator'S Manual

Search results

Summary of Contents for F36h

Reviews:

Related manuals for F36h

Brands by name

Popular brands