Bradley Terreon Quadra-Fount MF2944/BIR3 Installation Manual Download Page 10

MF2944/BIR3

 Installation

10  6/6/2014 

Bradley • 

215-1373 Rev. P; ECN 14-00-006

Cleaning and maintenance instructions for Terreon

Material Description: 

Terreon is an NAHB Certified densified solid surface material composed of polyester resin and is resistant to 

chemicals, stains, burns and impact . Surface damage can be easily repaired with everyday cleansers or fine grit abrasives .

Routine Cleaning: 

Clean daily or as often as conditions require using a standard commercial or household cleaner such as Formula 

409

®

 or Windex

®

 .

Stubborn Stains: 

Remove tough stains with Ajax

®

, Comet

®

, or Soft-Scrub

®

 and a green Scotch-Brite

®

 pad or lightly sand in a circular 

motion with 240 grit wet/dry sandpaper . The finish can be renewed with a maroon Scotch-Brite pad .

Special Situations for Material

Scratches: 

Remove scratches with a green Scotch-Brite

®

 pad . The finish can then be renewed with a maroon Scotch-Brite

®

 pad .

Hard Water Deposits: 

Remove hard water deposits with a mild solution of vinegar and water . Always rinse the unit thoroughly after 

cleaning .

Restoring the surface: 

Use Hope’s

®

 Solid Surface cleaner and polish to refresh and protect the Terreon Solid Surface material . 

Bradley recommends additional care and maintenance for the darker colored Terreon . For complete instructions on this additional 
maintenance see Bradley document #1505 .

Do not use strong acid or alkaline chemicals and cleansers to clean Terreon. If these chemicals come in contact with 

the terreon surface, wipe them off immediately and rinse with soapy water. 

 

Avoid contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and 

objects.

Repair Kits: 

Terreon repair kits are available . Contact your Bradley representative or distributor for part numbers and pricing .

 

Repair kits are made to order and have a shelf life of 30 days.

Brand Names: 

Use of brand names is intended only to indicate a type of cleaner . This does not constitute an endorsement, nor does 

the omission of any brand name cleaner imply its inadequacy . Many products named are regional in distribution, and can be found in 
local supermarkets, department and hardware stores, or through your cleaning service . It is emphasized that all products should be 
used in strict accordance with package instructions .

When cleaning units equipped with infrared (electronic eye) activation, it is helpful to turn off the power to the unit or cover the 
windows to prevent accidental activation. After the window is covered, the water will run for approximately 30 seconds and then 
shut off.

Summary of Contents for Terreon Quadra-Fount MF2944/BIR3















Reviews: