Bradley Terreon Quadra-Fount MF2944/BIR3 Installation Manual Download Page 1

Installation

MF2944/BIR3

Terreon

®

 Quadra-Fount

™ 

Washfountain 

with Battery Operated Infrared Control

(Standard*, Juvenile and OBC Height)

* Standard Height is ADA/TAS Compliant

IMPORTANT!

Read this entire installation manual to ensure proper installation. When 

finished with the installation, file this manual with the owner or maintenance 

department.

Separate parts from packaging and make sure all parts are accounted for 

before discarding any packaging material. If any parts are missing, do not 

begin installation until you obtain the missing parts.

Water supply requires a flowing pressure of at least 20 psi, but no greater 
than 80 psi. 

Make sure that all water supply lines have been flushed and then completely 
turned off before beginning installation. Debris in supply lines can cause 
valves to malfunction.

Hardware supplied by installer must be appropriate for wall construction. Wall 

anchors used must have a minimum pull-out rating of 1,000 lbs.

Product warranties may be found under “Product Information” on our web site 

at www.bradleycorp.com.

THIS

SIDE

UP

Packing List

Installation

Table of Contents

Pre-Installation Information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Parts Included with the Quadra-Fount

 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

Installation Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4-9
Cleaning and Maintenance   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .10-11
Troubleshooting .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .12-14

215-1373 Rev. P; ECN 14-00-006
© 2014 Bradley
Page 1 of 14 

6/6/2014

P .O . Box 309, Menomonee Falls, WI  53052-0309
Phone: 1-800-BRADLEY  Fax: (262) 251-5817
http:\\www .bradleycorp .com

Summary of Contents for Terreon Quadra-Fount MF2944/BIR3















Reviews: