Bradley EXPRESS SS-3/AST/JUV Installation Instructions Manual Download Page 9 | Manualshive

Page: 9 / 19

background image

Express® Lavatory System SS-Series

Installation Instructions - For Service Only

SS-3/AST/STD, SS-3/AST/JUV

9

Bradley Corporation •

215-1238 Rev. C; EN 03-813

5/11/04

Installation Instructions

continue . . .

Installation Instructions

continued . . .

Step 4: Connecting supply

1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™

Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a).

Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Connect the stop/strainer/check valve to the 1/2"
tempered supply line. Connect the flexible hose to the stop/strainer/check valve and air valve
manifold (see Figure 6b).

Figure 6a

FLEXIBLE

SUPPLY

HOSE

VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT TO

1/2" NPT COLD

WATER SUPPLY

CONNECT TO
1/2" NPT HOT

WATER SUPPLY

Figure 6b

CONNECT E TO
TEMPERED
WATER SUPPLY

FLEXIBLE

SUPPLY

HOSE

CHECK VALVE

1/2 NIPPLE

(113-006DJ)

«
...
7
8
9
10
11
...
»

Summary of Contents for EXPRESS SS-3/AST/JUV




















Reviews:

No comments

Related manuals for EXPRESS SS-3/AST/JUV

Brand: IB RUBINETTI Pages: 12

Citterio M 348131 Series

Brand: Axor Pages: 24

Brand: SportDOG Pages: 16

Brand: ESS Pages: 16

Pawfect Bathing System

Brand: Trendy Pooches Designs Pages: 11

Express DDTM008

Brand: Dash Pages: 32

ICONA CLASSIC R051

Brand: Fantini Rubinetti Pages: 24

Dog Auto Harness Fit & Tether

Brand: BERGAN Pages: 2

Brand: Danfoss Pages: 2

P299201LF Series

Brand: PEERLESS Pages: 6

Brand: Kohler Pages: 16

AXOR Starck 10635 Series

Brand: Hans Grohe Pages: 16

RETTANGOLO XL 26206

Brand: Gessi Pages: 2

Brand: Sanela Pages: 3

Brand: Sanela Pages: 5

Brand: Sanela Pages: 4

Brand: Sanela Pages: 5

Brand: Sanela Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands