background image

P.O. Box 309, Menomonee Falls, WI  USA  53052-0309
800 BRADLEY (800 272 3539)     +1 262 251 6000
bradleycorp.com

Installation

 

HDWP-INSTR-013 Rev. K; ECN 12-14-012

© 2014 Bradley

Page 1 of 21 

10/1/2014

Bradmar

 Restroom Partitions 

Overhead Braced - Series 400 

(includes No-Site style)

Table of Contents

Pre-Installation Information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Layout Dimensions for Brackets   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Mounting Brackets to Wall  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Leveling Bolts to Pilaster  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Brackets to Pilasters   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5–6
Pilaster Shoes   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Mounting Panels and Pilasters   .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7–8
Headrail   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Hinges   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10–14
Latch and Strike/Keeper   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 15–18
Stiffener Bracket .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Urinal Screens  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 20–21

IMPORTANT

Read this installation manual completely to ensure proper installation, then file it with the owner 
or maintenance department. Compliance and conformity to local codes and ordinances is the 
responsibility  of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding packag-
ing material. If any parts are missing, do not begin installation until you obtain the missing parts.

Leave the protective masking on until installation is complete. To prevent warping, always lay the 
material flat. Do not lean the material against the wall or stack unevenly. Allow 24 hours for material 
to adjust to site environment.

Use caution when drilling. Accuracy is important!

Partitions should be installed in a climate-controlled environment and shielded from direct sunlight.

Product warranties and parts information may also be found under ”Products” on our web site at 
bradleycorp.com.

Installation

THIS

SIDE

UP

Packing List

For Standard Height 

Doors and Panels Only

*HDWP-INSTR-013*

Summary of Contents for Bradmar 400 Series






















Reviews: