Sistema de retención infantil
26
27
5. INSTALLING CHILD SEAT. GROUP 2.
Use
group 2
only from approx. 4 to 6
years of age (15-25 kg)
WARNING
1.
From the base of the car seat, please change the
R
controller
from the base to the rear position by turning it on its axis (5.1).
2.
Remove the harness, buckle and cushion as described in
chapter
7
(5.2).
3.
The seat must be in its most upright position to adjust reclining
angle of the child seat, pull the control red handle
L
towards you
until the desired position is achieved
(5.3)
.
4.
Fit this child seat into the vehicle´s seat, making sure it is firmly
pressed against the vehicle seat backrest
(5.4).
5.
Place the child in the child car safety seat, fasten the belt, ensuring
that the vertical belt goes through
A
guide and that the diagonal
shoulder belt passes through
E
guides under both armrests (5.5,
5.6, 5.7 y 5.8).
6.
Insert the vehicle safety belt in the vehicle anchor point. You will
hear a “
click
” when properly installed, place the height adjuster
Q
so that the belt is tight and guide the belt over the child’s shoulder
into the correct position (5.9 y 5.10).
7.
Make sure the vehicle’s safety belt is not twisted, also check that
the seat cover does not impede the movement of the vehicle’s
safety belt or prevent the installation of the seat in any way. To
release your child unbuckle the vehicle safety belt as described in
the instructions.
Ensure that the belt has no slack.
Ensure that the belt has no slack.
Ensure that the belt has no slack.
4.
Slide over the vehicle´s diagonal belt from the
M
guideway from
the rear upper seat and the abdominal belt by the guides
I
, under
the car seat making sure to pass it on the inside base
R
controller,
so that it remains fastened by this (3.4, 3.5 y 3.6)
5.
Fasten the seat belt into the vehicle´s buckle until it “
clicks”
,
making sure the child seat is properly installed
(
(3.7).
4. INSTALLING CHILD SEAT. GROUP 1.
Only suitable for
group 1
, approx.
9 months to 4 years of age (9-18 Kg.)
WARNING
1.
From the base of the car seat, please change the
R
controller
from the base to the rear position by turning it on its axis (4.1).
2.
The seat must be in its most upright position to adjust reclining
angle of the child seat, pull the control red handle
L
towards you
until the desired position is achieved
(4.2)
.
3.
Fit this child seat into the vehicle´s seat, making sure it is firmly
pressed against the vehicle seat backrest
(4.3).
4.
Pass the seat belt through both
N
guides behind the seat (4.4, 4.5
y 4.6).
5.
Insert the vehicle safety belt in the vehicle anchor point. You will
hear a “
click
” when properly installed. (4.7).
6.
Tighten the lap belt and diagonal shoulder belt, then place the
red safety clip
T
on the diagonal shoulder belt tongue as near to
the vehicle anchor point as possible without touching it!
(4.8, 4.9
y 4.10).
7.
Make sure the vehicle’s safety belt is not twisted, also check that
the seat cover does not impede the movement of the vehicle’s
safety belt or prevent the installation of the seat in any way. To
release your child unbuckle the vehicle safety belt as described in
the instructions.
Always check that the harness straps are suitable for the height of
your child. The shoulders of the child should always be just below
the back slots at a suitable height (6.1).
BW123
www.babyqs.com
Child restraint system
Group 1/2/3
