Bpt KX12O16A Technical Manual Download Page 6

Page: 6 / 20

Flash for ON

Status response
Each channel can deliver a status response, depending on

the parameter settings. This always conveys the actual state

of the output (1= relay closed; 0= relay opened).
Parameters



Per channel: Select the relay mode “flash for ON” or

“flash for OFF”

Channel X: General
Parameter

Setting

Relay operation

make contact
break contact
changeover contact (channel 1:

make contact / channel 2: break

contact)
flash for ON
flash for OFF



Set the flashing interval for the device.

Flashing interval
Parameter

Setting

Flashing interval base

100 ms
1 s
1 min
1 hr

Flashing interval factor [5-255]

adjustable in single steps

open

closed

Relay

Status

actuated

not actuated

Switch (changeover contact for channel 1/2)

Status response
If two channels are combined into a changeover contact,

there is only one status feedback object when the status

response function is active.
This object always conveys the switching state of the

odd-numbered channel e.g. “1” (1= relay closed; 0= relay

opened).
Parameters



Per pair of channels: Select the relay mode “changeover

contact (channel 1: make contact / channel 2: break

contact)”

Channel X: General
Parameter

Setting

Relay operation

make contact
break contact
changeover contact (channel 1:

make contact / channel 2: break

contact)
flash for ON
flash for OFF

- Relay operation: flashing indicator

In the flashing indicator function, the relay opens and

closes automatically. A common flashing rate can be set for

all the channels via the “Flashing interval” parameter. The

frequency is calculated by multiplying a base value with a

factor.

Important

No short switching times may be parameterised

under load (see the technical data for the switch

output)

It can be selected whether the channel flashes for the value

“ON” (actuated) or “OFF” (not actuated). The value is the

product of combining the disable/higher priority function

with the switch object.

open

remains

open

closed

KNX

Relay status of

channel A

closed

remains

closed

opened

open

KNX

Relay status of

channel A

closed

open

remains

open

closed

Relay status of

channel B

closed

remains

closed

opened

open

Relay status of

channel B

closed

Switching on

Switching off

Summary of Contents for KX12O16A





















Search results

Summary of Contents for KX12O16A

Reviews:

Related manuals for KX12O16A

Brands by name

Popular brands

Bpt KX12O16A, Technical Manual

Search results

Summary of Contents for KX12O16A

Reviews:

Related manuals for KX12O16A

Brands by name

Popular brands