Bpt KX12O16A Technical Manual Download Page 14

Page: 14 / 20

Parameters



Per channel: Switch on the ON/OFF delay, staircase

lighting function and disable function.

Channel X: General
Parameter

Setting

Disable function

switched off
switched on

ON delay

switched on
switched off

OFF delay

switched on
switched off

Staircase lighting function

switched off
switched on



Per channel: Set the disable function.

Channel X: Disable
Parameter

Setting

Disable function for

Disable object = 0
Disable object = 1

Value of disable object after bus

voltage recovery

1
0

Reaction at blocking

no change
changes state
actuated
not actuated
flashes

Reaction at activation

no change
follows switch object
actuated
not actuated

Reaction at activation (with active

staircase lighting function)

follows switch object
not actuated



Per channel: Set the ON and OFF delay.

Channel X: Times
Parameter

Setting

Time base for ON delay -

100 ms
1 s
1 min
1 hr

Factor for ON delay

(1-255)

adjustable in single steps

ON delay is

not retriggerable
retriggerable

Time base for OFF delay -

100 ms
1 s
1 min
1 hr

Factor for OFF delay

(1-255)

120

adjustable in single steps

OFF delay is

not retriggerable
retriggerable



Set the flashing interval for the device if required.

Flashing interval
Parameter

Setting

Flashing interval base

100 ms
1 s
1 min
1 hr

Flashing interval factor [5-255]

adjustable in single steps

Important

No short switching times may be parameterised

under load (see the technical data for the switch

output)

- Disable function with switching delay/staircase light-

ing function
When the disable function is activated, it always switches

in the required direction without a delay. When it is deacti-

vated, the actuator likewise switches to the required state

without a delay. The last switching telegram is saved during

a disable function and any delay periods or staircase timers

continue to run.

Disable function for: Disable object = 1; Value of disable object after bus
voltage recovery: 0; Reaction at blocking: no change; Reaction at activa-
tion: follows switch object: Relay: make contact

Communication objects
The following communication objects can be selected:
Per channel:

Function

Object name

Type

Prio

Flags

Behaviour

Channel X

Switch object

1 bit

Low

Receive

Channel 1,

2,...

Disable object

1 bit

Low

Receive

KNX

telegram,

switch object

Relay status

closed

open

t staircase

KNX

telegram,

disable object

disabled

Summary of Contents for KX12O16A





















Search results

Summary of Contents for KX12O16A

Reviews:

Related manuals for KX12O16A

Brands by name

Popular brands

Bpt KX12O16A, Technical Manual

Search results

Summary of Contents for KX12O16A

Reviews:

Related manuals for KX12O16A

Brands by name

Popular brands