background image

19

Applicable  to  Periodic  Services

1. Wash  the  vehicle.
2. Flush  &  change  Engine  oil  /  Top  up  Oil  Level  (As  per  Schedule).
3. Clean  air  filter.  (Replace,  As  per  Schedule).
4. Check  and  clean  fuel  line.  (Replace  filter,  if  required  -  If  Applicable).
5. Clean  oil  filter.  (Replace,  As  per  Schedule  -  If  Applicable).
6. Clean  oil  strainer  As  per  Schedule.  (Replace,  if  required  -  If  Applicable).
7. Clean  &  Drain  Carburetor.  (Overhaul,  if  required).
8. Clean,  Check  &  Adjust  spark  plug  gap.  (Replace  As  per  Schedule).
9. Check  &  Correct  Wheel  Run-out.  (If  Applicable).

10. Check  &  Adjust  air  pressures  in  the  tyres.
11. Check  &  adjust  (if  required)  valve  clearance.  (As  per  Schedule  -  If  Applicable).
12. Adjust  chain  slackness.  Clean  &  Lubricate  Chain,  If  required  (As  per  Schedule  -  If  Applicable).
13. Check  &  adjust  brakes.
14. Check  and  top  up  brake  fluid  level  (If  Applicable).
15. Check  and  adjust  steering.
16. Check  /  Replace  Fork  Oil,  As  per  Schedule  (If  Applicable).
17. Check  Clutch,  Gear,  Choke,  Accelerator  &  TPS  (If  Applicable)  and  adjust  if  required.
18. Check  &  tight  Nuts,  Bolts  &  Fasteners  to  the  recommended  torque  (Refer  SSM).
19. Lubricate  specific  points  as  per  Lubrication  Schedule.
20. Check  Battery,  top  up  Distilled  Water.  Route  the  cables  and  fit  terminal  caps  properly  Clean 

terminals  &  apply  Petroleum  Jelly  (If  Applicable).

21. Check  all  Meters  for  proper  functioning.
22. Start  vehicle,  check  &  adjust  Horn  &  All  Lights   for  proper  functioning.
23. Start  vehicle,  check  idling  and  CO%.  Tune  Engine  &  Carburetor  if  required.
24. Carry  out  any  additional  work  if  required.
25. Test  Ride  the  Vehicle   if  required. 
26. Clean  the  vehicle  at  the  time  of  delivery.

Summary of Contents for BM 100












Reviews: