Bose FREESPACE 4400 Service Manual Download Page 75

Page: 75 / 107

TROUBLESHOOTING

Bad sound in a zone

Bad sound

Is the sound

unnatural?

Verify that the correct Speaker EQ
is selected in the FreeSpace 4400
Installer ™ software for that zone.

Verify that the loudspeakers are
wired in phase. Check the rear pan-
el markings.

Yes

Reduce the input gain using
FreeSpace 4400 Installer ™ soft-
ware until the indicator is solid
green.

Verify that the input source signal
is clean. If source is from a mixer,
decrease the mixer gain.

Is the AMP OUTPUT

indicator flashing?

Are input and

output indicators green

and sound is

distorted?

Verify source

hardware settings

Yes

Verify that the loudspeakers are
not being overdriven or are dam-
aged.

Verify that the total load imped-
ance presented to the FreeSpace
4400 output is within specified
limits for the selected mode of
operation.

Is the input signal

clean at the FreeSpace

4400 input?

Yes

Auto Volume does not calibrate

Auto Volume calibration may fail if the
process cannot obtain an adequate source
level. This may be due to:

• Loudspeakers are tapped too high
• Maximum output gain is less than -20 dB
• Source is not operating
• Source level is too low

Calibration could also fail if the calculated
loop gain is not within required limits. This
may be due to:
• Broken microphone cable
• Loudspeakers are not connected
• Sensing microphone is not connected, or is
connected to the wrong zone

Summary of Contents for FREESPACE 4400












































































































Search results

Summary of Contents for FREESPACE 4400

Reviews:

Bose FREESPACE 4400, Service Manual, Page: 75 / 107

Search results

Summary of Contents for FREESPACE 4400

Reviews: