Bosch Rexroth UPE2 General Operating Instructions Download

Page: 25 / 56

RE 51150-B/07.11 | Drive modules

Bosch Rexroth AG

25/

Transport and storage

When storing and transporting the product, always observe the ambient condi-

tions specified in Chapter 6.2

"Storing the drive module"

If the package has to be opened e.g. for inspection purposes, you should

reseal the packaging to the condition in which it was supplied.
Wherever possible, the packaging should not be removed until directly before

assembling the unit.

Transporting drive modules

6.1

Preparing the drive module for transport

6.1.1

The following preparations must be carried out before transport:

Check the space required for the installation of the drive module at the place

of use.
Check the transport route. Depending on the method of transport, allow for

additional space around the drive module.
After previous operation operation of the drive module, depressurize the

installed accumulators on the oil side. If possible, reduce the pressure on the

gas side to a value of 2 bar (200 kPa).

Bosch Rexroth always delivers drive modules without hydraulic fluid. Any

deviations from this rule are described explicitly in the product-specific

documentation. From the factory inspection there may, however, still be oil

residues in the product.

Manual transport

6.1.2

CAUTION

Hazard due to overload and/or unsuitable gesture during lifting

and transport!

Most severe injuries and injuries that adversely affect posture!

Completely drain the drive module.

Secure the drive module for the transport within the company, e.g. by means

of a pallet.
Only lift the drive module using attachment devices or suitable lifting gear.

Transport using forklifts and similar floor conveyors

6.1.3

When using floor conveyors, e.g. forklifts, the drive module may only be trans-

ported by personnel who can prove they hold the relevant qualifications, including

safety training, for the respective device.
You should proceed as follows:

Secure the drive module at the floor conveyor against tilting. For this purpose,

use suitable attachment devices like e.g. tie downs.
Do not fasten attachment devices at the control modules.

Summary of Contents for Rexroth UPE2

























































Search results

Summary of Contents for Rexroth UPE2

Reviews:

Related manuals for Rexroth UPE2

Brands by name

Popular brands

Bosch Rexroth UPE2, General Operating Instructions

Search results

Summary of Contents for Rexroth UPE2

Reviews:

Related manuals for Rexroth UPE2

Brands by name

Popular brands