background image

2

 |  Operating instructions | 

OBD 1110

 |

en

OBD 1110

 | Operating instructions  | 

3

en

577383 REV A | 10.2015

Bosch Automotive Service Solutions

577383 REV A | 10.2015

Bosch Automotive Service Solutions

Table of Contents

Safety Precautions  .  .  .  .  .  .  .  .  . 3

Signal Words and Symbols   . 3

Important Safety Messages  .  . 3
About the Tool    .  .  .  .  .  .  .  .  .  .  .  . 4
Tool Parts   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Icons   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Connect the Tool    .  .  .  .  .  .  .  .  .  . 5
Diagnostic Menu User  

Interface   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Read Codes  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Vehicle Selection   .  .  .  .  .  .  .  .  .  . 7
Erase Codes   .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
MIL Status  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
I / M  Monitors  (Emissions)   .  .  . 8
View Freeze Data   .  .  .  .  .  .  .  .  .  . 9
VIN  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
System Setup   .  .  .  .  .  .  .  .  .  .  .  .  . 9
View Data   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Troubleshooting   .  .  .  .  .  .  .  .  .  . 10
PID Definitions   .  .  .  .  .  .  .  .  .  .  . 10
Limited Warranty   .  .  .  .  .  .  .  .  . 15

Disclaimer    .  .  .  .  .  .  .  .  .  .  .  . 15

Software .  .  .  .  .  .  .  .  .  .  .  .  .  .  15

Technical  Support / Repair 

Service     .  .  .  .  .  .  .  .  .  .  .  .  .  . 15

Declaration of Conformity  .  . 16

Safety Precautions

This user guide describes the 
features of the tool and provides 
step-by-step instructions for 
operating the tool . Always refer 
to and follow safety messages 
and test procedures provided by 
the manufacturer of the vehicle 
and the tool .

Read and understand 
the user guide before 
operating the tool .

An undetected or uncorrected 
vehicle malfunction could cause 
a serious, even fatal, accident . 
Important safety information in 
this user guide is intended to 
protect the user, bystanders, and 
the vehicle .

Signal Words and Symbols 

WARNING!

Indicates a possible 
hazardous situation 
that, if not avoided, 
could result in death 
or serious injury to op-
erator or bystanders .

NOTICE

Indicates a condition 
that may result in lost 
information .

 

B

Indicates a single-

step procedure .

Important Safety 

Messages

WARNING!

This tool may not 
detect every malfunc-
tion . Do not take 
chances with brakes, 
steering, or other vital 
functions of the vehi-
cle . A serious accident 
could result .

Always wear ANSI-
approved goggles for 
eye protection .

• 

Before testing a vehicle, make 
sure the transmission is in 
PARK (automatic transmis-
sion) or NEUTRAL (manual 
transmission) and the parking 
brake is set .

• 

Never lay tools on the vehi-
cle battery .

• 

Battery acid can burn . If 
contacted, rinse with water 
or neutralize with a mild 
base such as baking soda . If 
you splash your eyes, flush 
with water and call a physi-
cian immediately .

• 

Never smoke or have open 
flames near vehicle . Vapors 
from gasoline and battery 
are explosive .

Summary of Contents for OBD1110












Reviews: